Product Description
Navimare Alkyd Primer is a high-build alkyd primer loaded with non-toxic pigments for an excellent protection of all above waterline areas. The product has good levelling properties and is easy to apply.
Technical Properties
| Colour / Texture | : Red and White / Matt |
| Volume Solids | : 50% |
| Specific gravity | : 1.4 gr/ml |
| Volatile organic compounds | : 412 gr/liter |
| Flashpoint | : >25°C |
Surface Preparation
- Steel — Oil and grease should be removed by solvent cleaning or by using Gelclean followed by fresh water cleaning. Remove weld spatter and smooth weld seams and sharp edges. Abrasive blasting: min. Sa 2.5 – ISO 8501:1. Remove dust and debris and apply the first coat immediately. Apply 2–3 coats.
- Corroded areas — Should be power tool cleaned to ISO-St3 or blast cleaned to ISO-Sa2 or better. Existing systems should be dry and free from fouling, loose paint, salt, grease and other contaminants. Apply 2–3 coats.
- Wood — Ensure surface is dry. Sand thoroughly and remove dust. Degrease if necessary. Apply 1–2 coats.
Usage Instructions
Substrate should be dry and free from contaminations. Relative humidity should be less than 90% RH. Thin if necessary with 0–5% of the specified thinner. Mix well to a homogeneous paint. When applied by brush or roller, apply in smooth and gentle strokes. Apply crosswise to ensure even distribution. Avoid excessive application. Wear protective clothing, goggles and gloves. Refrain from smoking at all times.
Application Data
| Mixing ratio by weight | : Single pack |
| Potlife | : Not applicable |
| Dry film thickness per coat | : 40 micron |
| Wet film thickness per coat | : 80 micron |
| Theoretical coverage | : 12.5 sq.m/liter |
| Thinner | : Navimare Alkyd Thinner 7600 |
| Surface Temperature | : Min 1°C / Max 40°C |
Spray Equipment Data
| Conventional Spray | Airless Spray | |
| Nozzle orifice | 1.2–2.0 mm | 0.38–0.53 mm |
| Air pressure | 3–5 bar | 120–180 bar |
| Volume of thinner | 0–10% | 0–3% |
| Practical spreading rate (m²/l) | 6.8 | 8.7 |
Drying and Recoating Times
| Substrate temp. | Dry to recoat | Hard dry | Maximum recoating (1) |
| 10°C | 8 hours | 24 hours | Indefinite |
| 23°C | 6 hours | 16 hours | Indefinite |
| 30°C | 4 hours | 12 hours | Indefinite |
(1) The surface should be dry and free from salts and other contaminants prior to overcoating. The best intercoat adhesion is achieved when the subsequent coat is applied before the preceding coat is fully cured. After prolonged exposure times it may be necessary to roughen the surface in order to ensure intercoat adhesion. When in doubt, consult your nearest Navimare office.
Health and Safety
Observe the precautionary notices on the label of the container. A material safety data sheet is available upon request and national or local safety regulations should be followed.
- Avoid skin and eye contact by wearing overalls, gloves, goggles, mask, etc.
- Spillage on the skin should immediately be removed by thorough washing with lukewarm water and soap or a suitable industrial cleaner.
- Eyes should be flushed with fresh water and medical attention sought immediately.
- Spraying should be carried out under well-ventilated conditions. Avoid inhalation of solvent vapours and paint mist by wearing an air mask.
- This product contains flammable materials and should be kept away from sparks and open flames. Smoking in the area should not be permitted.
Disclaimer
The information in this data sheet is provided to the best of our knowledge. However, we have no control over either quality or condition of the substrate and other factors affecting the use and application of this product. Therefore, we cannot accept any liability whatsoever or howsoever arising from the performance of the product or for any loss or damage arising from the use of this product. We reserve the right to change the product without notice.
