Epoxy Light Weight Yacht Filler SF LW
Light Weight Epoxy Yacht Filler
Catalog No: 800-K-XXXX
FEATURES
- Resistant to many acid, alkali and solvent splashes even at 65°C
- Excellent resistance to abrasion and chemicals
- Smooth and easily cleanable surface
- Solvent-free
RECOMMENDED USES
An easily sandable filler and fairing compound. Must be cured with Epoxy Polyamine adduct. Specially developed as a lightweight filler for yachts, but also suitable for:
- Floor coating in chemical processing plants
- Mining and metal processing operations
- Steel, textile and pulp-and-paper mills
- Wastewater and waste treatment facilities
- Food and beverage factories
SPECIFICATION DATA
| Color | : Red-Pink (mixed) |
| Density (at 20°C) | : dA=0.75 / dB=0.50 / mix A+B=0.63±0.02 Kg/Lt. |
| Packaging | : Metal buckets 5.00 Lt or 10 Lt kits. Two-component. A/B=3.00/2.00 by weight or 1.00/1.00 by volume. |
| Gloss | : Matt |
| Flash Point | : >60°C in mixture. Setaflash |
| Cleaning thinner | : Do not thin; use Ema T-10 thinner for cleaning only. |
| Pot Life | : 20 minutes (at 23°C). Working and drying times depend on temperature. |
| Shelf life | : More than 1 year. Store unopened in original packaging at 5–35°C. |
| VOC | : 0 gr/lt. |
| Volume Solids | : 100% |
| Temperature Resistance / Application Temperature | : 121°C dry // Product 10–35°C, Atmosphere 10–35°C, Substrate 10–35°C |
| Theoretical Coverage | : 0.2 m²/Lt at 5 mm wet thickness |
| Recommended Application Thickness | : Maximum 2 cm |
| Application Method | : Trowel, putty knife, levelling trowel |
| Maximum Substrate Moisture | : 3% |
| Drying Time (23°C) | : Sandable: 16 hours. Overcoat with filler min: 24 hours. Overcoat with paint min: 2 days. Max: Indefinite. |
APPLICATION GUIDE
Surface Preparation
Surface must be clean and dry before application. There must be no dust, dirt, oil or moisture on the substrate. During application, substrate and material temperatures should be 18–28°C. Moisture content of the prepared substrate measured at approximately 2 cm depth should not exceed 3%.
Mixing and Thinning
Use a suitable mixer. Only mix complete units as supplied in the packaging. Add the hardener (B) to the base material and mix for 3 minutes until a homogeneous mixture is obtained. Then transfer the mixture to an empty container and mix again until homogeneous.
Application
Previously painted surfaces should be cleaned, dried, sanded with 180–200 grit sandpaper and repaired if weak. After application, sand wet or dry with 60–120 grit sandpaper. Spread the mixture on a surface to avoid excessive heat build-up and extend working time. Do not apply more than 2 cm thick in one application. Do not apply at temperatures below 7°C. Do not thin.
SAFETY PRECAUTIONS
Read the MSDS Material Safety Data Sheet for safety rules and warnings. Prevent skin and eye contact (gloves, protective goggles, face mask and industrial barrier cream). Ensure adequate air circulation. If paint contacts skin, wash with lukewarm water and soap. If splashed in eyes, rinse for at least 10 minutes and seek medical attention. Contains flammable components — keep away from sparks and open flames. No smoking permitted. Read all cautionary notices on containers.
NOTE
All information in this technical bulletin may be subject to change from time to time as a result of experience, developments in raw materials and research and development activities. For additional information, please contact your regional sales representative or Navimare-PX Istanbul directly.
